Follow

Check resistance ANT

THIS PROCEDURE WORKS ONLY WITH THE "ANT" TRAINERS, NOT WITH THE "B+" TRAINERS. 

COMPATIBLE TRAINERS : 

 - REALTOUR ANT
 - REALAXIOM ANT
 - REALPOWER ANT
 - REAL E-MOTION ANT
 - REALTURBOMUIN ANT

NOT COMPATIBLE TRAINERS :

 - REALTOUR B+
 - REALAXIOM B+
 - REAL E-MOTION B+
 - REALTURBOMUIN B+

 

To test if the resistance unit works properly, or it has hardware problems, it is necessary to verify something without software.

There are two modes: Stand Alone mode ( manual management of resistance through the console not available RealTour and Real Emotion ), or by using a software called AxtoANT support .

 

The operations to follow are the following :

 

Stand alone: ( only in case of RealAxiom ANT and RealPower ANT )

- Remove the power supply from the trainer.

- Remove the batteries from the console

- Insert the batteries on the console and avoid to hold your hand in contact with the front touch otherwise the calibration of the keys is carried out incorrectly.

- The console has 3 LEDs , if the right one blinks , proceed to the next step , otherwise press the touch "up arrow" and "down arrow " keys simultaneously until the right LED begins to flash.

- Insert the jack the power supply ( in the case of the unit RealAxiom , at this time the step motor moves inside the unit , producing a small vibration for a few seconds ) ( only in case of RealTourANT and RealAxiom ANT )

- Start pedaling and press the "up arrow" until the right LED does not blink very often

- Note if you feeling more resistance by the roller.

 

Software AxtoANT Mode ( compatible with all the trainer ANT ):

- Remove the power supply by the unit

- Remove the batteries by the console ( only in case of RealAxiom ANT and RealPower ANT )

- Insert the batteries in the console avoiding to hold your hand in contact with the front touch otherwise the calibration of the keys is carried out incorrectly. ( only in case of RealAxiom ANT and RealPower ANT )

- The console has 3 LEDs , if the right one is NOT flashing , proceed to the next step , otherwise press the touch "up arrow" and "down arrow " keys simultaneously until the right LED stops flashing. ( only in case of RealAxiom ANT and RealPower ANT )

- Insert the jack the power supply ( in case of RealAxiom , at this time the step motor moves inside the unit , producing a small vibration for a few seconds ) ( only in case of RealTour ANT and RealAxiom ANT )

- Check that the ANT USB stick is plugged into the computer 

- Download this file ANT

- Unzip the ANT.zip file

- Run the software AxtoANT.exe

- Change the Roll diameter value depending on the unit you are going to connect , RealTour = 30, RealAxiom = 40 , RealPower = 45 , Real Emotion = 85 , RealTurboMuin = 150 as in the picture and arrow "Yellow"

 - unflag the HR and Console flag up to the Connect button

- Press the Connect button , as in the picture and arrow "Green"

 

- Wait until a confirmation message appears on the screen that says "Connected"

- To check that the unit is connected , click Update , as shown in the picture with "Light Blue" arrow and check the unit serial panel on ( comparable with the value written on the label attached to the unit) .

- Enter the average value inside the box the value 150 , and press the " Send Resistance" as in the picture with " Red " arrow

- Then check that the resistance increases and that all values ​​are read by pressing the "Start" button , as indicated by the arrow in the image with "Black" arrow

- You can check all the values on the panel under the black arrow, and feel the resistance changing.

Was this article helpful?
0 out of 0 found this helpful
Have more questions? Submit a request

Comments

Powered by Zendesk